A 1960-72 John Deere 3020, plus the 3010. Diesel, gas or LP, Syncro-Range or Power Shift, wide front, Roll-O-Matic or a single front wheel. Then hang a loader, forks or a rotary cutter on it, or set it up to pull.

14 configs

• 3020 Diesel (the default): 4.4 L four, 71 PTO hp, Syncro-Range 8 forward / 2 reverse
• 3010 Diesel: the 1960-63 original, 59 PTO hp, galvanized straight stack
• 3020 Gasoline: the 227 ci gas four, 64 PTO hp
• 3020 LP Row-Crop: LP engine with the tank through the hood, on the Roll-O-Matic narrow front
• 3020 Diesel ROPS Canopy: Roll-Gard canopy and a chrome stack
• 3020 Diesel Power Shift: 8 forward / 4 reverse that shifts under load with no clutch
• 3020 Gasoline Power Shift, Single Front: one front wheel on a fork, for narrow rows
• Ballasted Workhorse: cast wheel weights, front suitcase weights, bar-lug rears
• Duals and Stacked Weights: dual rears with two sets of cast weights
• John Deere 148 Loader: 72 in bucket, 3.2 m to the pin
• 148 Loader with Pallet Forks: forks on the loader and on the 3-point hitch
• 606 Rotary Cutter, Road Kit: 6 ft cutter on the PTO, seat umbrella, SMV sign and fender flashers
• Farm Stock Puller (8,500 lb class): factory engine and tires, weighed to the class
• Hot Farm Puller (9,500 lb class): single turbo, about 300 hp at 3,000 rpm, pulling tires, wheelie bars and a kill-switch mast

Every config can show up at private sellers in career and can be insured.

The loader and the cutter

• John Deere 148 loader with a bucket or a pin-on pallet fork frame. It runs off the engine pump, so it moves faster with the hand throttle up
• The valve levers by the seat move with the controls, and you can work them with the mouse
• 42 in pallet forks on the 3-point hitch stay level as it lifts
• John Deere 606 rotary cutter: turn on the 540 PTO and the blade spins up to about 890 rpm, then coasts down when you shut it off

Working parts

• Hood, grille, fenders, platform, hitch and drawbar are separate parts. Swap them off, or crash and watch the panels crumple and tear away
• Roll-O-Matic front: the two wheels are geared together, so one rises as the other drops
• Pedals, gear lever, hand throttle, rockshaft lever and loader levers all move
• Factory muffler with a rain flap that lifts with the throttle, or a chrome, galvanized or tall open pulling stack
• Duals, 1 to 3 sets of wheel weights and 11 rim finishes, from factory yellow to polished aluminum and chrome
• Diff lock, rear PTO, headlights, a rear work light, a disc horn you can click on the dash, and fender warning lamps that flash with the turn signals
• The drawbar hitches vanilla trailers
• Uses the new 0.40 driver figure in the seat

Tractor pulling

The drawbar pin height and setback are inside the usual pulling rules, and the class weights include the driver. Hook up the sled chain, set the hot farm loose and watch the front come up onto the wheelie bars.

Controls

• 3-point hitch: Y and U to raise and lower
• Loader: T and G to raise and lower the boom, I and K to curl and dump
• PTO: O
• Diff lock: in the vehicle features menu
• Gamepad: hold the modifier, right stick lifts and left stick tilts

Install

Don't unzip it. Drop the zip into your BeamNG mods folder:
%LOCALAPPDATA%\BeamNG\BeamNG.drive\current\mods\
It's under John Deere 3020 in the vehicle selector. Needs BeamNG.drive 0.40 or newer and no other mods. The full guide to every part and control is in the README inside the zip.